SAM2P(1)

NAME
sam2p - program to convert raster images to PostScript, PDF, and other formats

SYNOPSIS
sam2p [options] infile outfile
sam2p [options] jobfile

DESCRIPTION
This manual page documents briefly the sam2p command. It was written for the Debian distribution because the original program does not have a manual page. The complete documentation can be found in /usr/share/doc/sam2p/README.gz

sam2p is a program that converts many raster (bitmap) image formats into Adobe PostScript or PDF files and several other formats. The images are not vectorized. sam2p gives full control to the user to specify standards-compliance, compression, and bit depths.

sam2p can operate in two modes: one-liner mode and job mode. In job mode the user has to write a ``job'' file which specifies the conversion parameters and allows full control of all aspects of the final output. This manpage deals only with one-liner mode, see /usr/share/doc/sam2p/README.gz for details on job mode.

EXAMPLES
To convert an image file to EPS, use:
     sam2p infile.gif outfile.eps The output format is guessed from the file extension. Optionally, the output format also can be specified as option or as prefix to the output file. For example, the following commands produce postscript level 3:
     sam2p infile.gif psl3:outfile.ps

     sam2p -ps:3 infile.gif outfile.ps sam2p can include its own (zip and lzw) decompression filter in Postscript files, allowing better compression than normally supported by Postscript level 1:
     sam2p -1 -c:zip infile.gif outfile.ps
     sam2p -1 -c:lzw infile.gif outfile.ps

OPTIONS

-1, -ps:1, psl1:
    produce Postscript Level 1

-1c, -ps:1c, pslc:
    produce Postscript Level 1 with the CMYK and `colorimage' extension

-2, -ps:2, psl2:
    produce Postscript Level 2 (default for postscript)

-3, -ps:3, psl3:
    produce Postscript Level 3

-pdf:b0, pdfb1.0:
    produce PDF version 1.0 (BI inline image)

-pdf:b2, pdfb1.2:
    produce PDF version 1.2 (BI inline image) (default for PDF)

-pdf:0, pdf1.0:
    produce PDF version 1.0 (XObject image)

-pdf:2, pdf1.2:
    produce PDF version 1.2 (XObject image)

-e:0, -e:none
    don't scale

-e, -e:1, -e:scale
    scale image to fit page

-e:rot, -e:rotate
    scale and rotate image to fit page (default if output filename has .ps extension)

-m:dimen
    set all page margins to dimen
    dimen can have one of the following units (as in TeX): bp, in, pt, pc, dd, cc, sp, cm, mm

-m:spec:dimen
    set spec margin(s) to dimen (spec can be l, r, t, b, v (top and bottom), h (left and right))

-m:dpi:res
    set output EPS or PDF to resolution 72*72/res dpi

-m:dpi:-res
    set output EPS or PDF to resolution res dpi

-c:none, -c:lzw, -c:zip, -c:rle, -c:fax, -c:dct, -c:jpeg
    select compression type (support depends on output format)

-j:quiet
    print only error and fatal error messages, suppress warnings, notices etc. Must be put at the beginning of the command line to suppress initial banners, too.

--  If not the last argument: treat all further arguments as files (required if a filename contains a colon or starts with a minus)
    If the last argument: use input filename as output filename (i.e. overwrite input file).

SUPPORTED FILE FORMATS

Input formats:
    PNM, PBM, PGM, PPM, XPM, GIF, LBM, TGA, PCX,
    JPEG (requires djpeg from package libjpeg-progs),
    TIFF (requires tifftopnm from package netpbm),
    PNG (requires pngtopnm from package netpbm),
    PS, EPS, PDF (require ghostscript)

Output formats:
    XWD, BMP, PNG, TIFF6, JPEG, PNM, GIF89a, XPM, PS (levels 1,2,3), EPS (levels 2,3), PDF (1.0 and 1.2)

    For some formats, sam2p supports transparency. See the README file for more info.

SEE ALSO
The program is documented fully in /usr/share/doc/sam2p/README.gz

AUTHOR
sam2p was written by Szabó Péter <pts@fazekas.hu>.

This manual page was written by Stefan Fritsch <sf@sfritsch.de>, for the Debian project (but may be used by others under the terms of the GNU General Public License, Version 2).